Table Saw - SCM SI12

Tags: #<Tag:0x00007fa49b3578b0>

Notice

  • This machine should not be operated without induction.
  • This tool should not be used while alone in the space - lone working rule.
  • This machine should not be left unattended during operation.

If you believe that any of the information contained on this tool page is misleading or could otherwise be improved, please notify @woodtechs.

SCM SI12 Table Saw


click/tap to expand for photo

This is a heavy-duty table saw.

Details and dimensions:

(click/tap to expand)

Fixed table size: 645 x 840 mm
Sliding table size: 300 x 1500 mm
Saw blade tilting: from 90 deg. to 45 deg.
Fence for cutting width up to: 2600 mm
Cutting width on parallel fence: 1000 mm
Max saw blade diameter: 300 mm
Min saw blade diameter: 250 mm
Max. cutting height at 90 deg. : 100 mm
Saw blade speed: 4000 rpm
Motor: 4 hp
Net weight: 430 kg

PPE / Safety Checklist

All of these rules must be obeyed at all times. A failure to comply may result in a ban.

  • Do not let any part of your body or clothing come within 30cm (1ft) of the blade whilst it is moving. Instead, use push sticks with a notched end to retain greater control (more on this below).
  • The blade guard must always be in place and set to the right height. The sole exception to this is when using a jig that keeps the blade entirely covered throughout the entire cut.
  • Do not wear loose clothing.
  • Ensure long hair, jewellery, and any clothing drawstrings are securely tied back
  • Safety glasses are mandatory
  • Extraction must be used at all times
  • Masks should be used by all woodshop users for MDF and hardwoods - see general woodshop induction notes
  • Ear defenders or ear plugs should be worn and offered to other people in the shop, as this is a very loud tool.
  • Sensible footwear with sturdy toes and a small heel should be worn at all times in the workshop. Steel toe-caps are a bonus.
  • Do not wear gloves - they are an entanglement risk with woodworking machine tools
  • As with any power tool - be sober and alert. Do not use the table saw when tired.
  • Always isolate the tool (turn off the power) before going within 30cm of the blade, or exposing the blade.
  • the no lone working rule applies to the table saw - another adult must be at SLMS
  • No partial cuts. HSE rules dictate you can’t make a partial cut without a relevant guard.
  • No dado stacks

Acceptable and unacceptable materials to cut

  • Exceedingly bowed or warped wood must be flattened first- it must be able to run flat on the tablesaw bed without rocking.
  • When using the rip cut fence, the edge of the wood running along the fence must be flat and straight
  • Perspex may be cut, but only when using the designated saw blade.
  • Wood sheet goods, like MDF or plywood, may be cut.

Condition Notes

Purchased 2nd hand. 1980s vintage Italian engineering. Bespoke blade guard / extraction fitted.

Owners

@asander1

Risk Assessment

Table Saw Risk Assessment

Induction and Training:

Tablesaw Induction Waiting List

Expand for Assessment details

What to do ahead of time

The expectation ahead of an assessment is that you have thoroughly read through the material on this page, and are comfortable demonstrating your ability to safely use the tool. If necessary, watch the videos at the bottom of the page. Please be considerate of your inductor’s time.

Before being able to request an assessment, you must get a 100% on this quiz to show that you understand the safety precautions and theory behind the tool: Table Saw Assessment Quiz

What to bring

Something to rip and cross cut without help lifting/moving

What will be covered

In the practical assessment you will show the trainer you can use the Table saw safely by:

  • Describing the acceptable and unacceptable materials to cut on the table saw
    • material thickness, material shape, material type
  • what do you do if something is broken, doesn’t sound correct, feels off, etc?
  • Demonstrating the inspections you should make before using the table saw
  • Setting the blade, fence, and guard for a rip cut
  • Turning on the extraction
  • Making a rip cut
  • Changing the blade to a crosscut blade - describe how to
  • Setting up the crosscut side table
  • Making a cross cut
  • Cleaning up

The inductor will focus on your stance and technique when making a cut. Remember, hands never within 30 cm of the blade - use a push stick

Feel free to ask your inductor any questions during the

What the table saw does:

The table saw is used to make accurate, clean, straight cuts into boards that are less than 4 inches thick. It can handle full size 8ft by 4ft boards. It does this using a large, circular saw blade that is built into a table - which provides a large flat surface to slide the workpiece over. It can also be used for precise angled cuts - when crosscutting, the fence can be set to any angle, to produce a finished piece with a more or less “pointy” end, rather than simply a perfectly flat 90 degrees.

It is an alternative to the band saw for some applications. The band saw can cut deeper materials and handle some curves, whilst the table saw is designed to cut perfectly straight, at a variable depth and angle, and handle larger workpieces (provided they are not too thick). Ripping down large sheets is one of the most common tasks.

Anatomy of the tool

(click/tap to expand)
  • Power control -Once the power is activated by tool control, you can isolate/de-isolate the machine using the switch on the wall, then use the green power button on the table saw controls to turn it on. ALWAYS isolate the machine before getting close to the blade. This applies to any powered tool in the workshop

  • Emergency stop - as well as the red push stop button next to the power button, there is also an emergency stop button on the end of the slide for the table saw, to make sure the operator can always reach one easily if needed. Remember - emergency stop buttons are generally damage limitation - bad things are usually already happening by the time they are hit. Try to avoid this by preparing carefully.

  • Controls - the controls for the table saw are accessible from the operator’s position. These are explained in more detail in the relevant sections below.

  • Bed - this is the large, flat steel surface with a gap in the middle containing the blades. You will feed your material over the bed, through the path of the blade, and out the other side. The bed on the far side/downstream end of the blade has been extended - so that larger pieces of material can be fed thorough it without “falling off” the other end. Anything up to 5ft in length can potentially be managed by a single operator. However, anything over 5ft would fall off the end before cutting had safely finished, so a second person is needed to hold the end of the material coming off the bed, keeping it straight and level.

  • Guard - a metal arm hangs over the table saw, and holds a transparent plastic guard over the main blade. The guard is designed to hang just above the surface of the bed, and then rise up as a workpiece is pushed underneath it. As the material clear the back of the guard, it then lowers itself back down to cover the blade. This is a safety feature. The base height of the guard is controlled by a wheel on the “elbow” of the arm. The guard should always be in place, unless a specific task is being carried out with supervision by a woodtech.

  • Extraction - there are two elements to the table saw extraction system. One line has been fed into the body to extract sawdust directed down from the blade (this is where most of it is deposited), whilst the other follows the arm and feeds from inside the top of the transparent guard (which allows for the extraction of finer particles). Always ensure the extraction is on when using the table saw - although a relatively small amount of dust is released into the workshop, it piles up enormously under and around the table saw body itself. This poses a fire risk if not kept clean.


    when the extraction is on, check the gauge to make sure the system is running at full pressure. If the needle is not all the way to the left, close the gates behind the sanders

  • Rip-cut fence - this is the metal bar on top of the bed, which always remains perfectly parallel to the blade. It can be moved closer to or further away from the blade. This fence should be used when ripping along the grain of a board or plank. The fence is moved using a combination of the black plastic locking handles on top of it, and various controls on the front of the table saw. These are explained in more detail below.

  • Sliding beam - the side of the table saw bed on the left (from the operator’s position) can slide backwards and forwards to allow for easier movement of material past the blade without twisting or catching. This is commonly used with the next item…

  • Removable side table - this is an extension weighing 19kg, which is added to the table saw to allow larger materials to be catered for - especially when cross-cutting. This is linked to the sliding beam, and can be used either in a fixed position, or with travel parallel to the blade. Note that this is heavy and moderately awkward to fit correctly whilst supporting its weight. It is strongly advised that this be a two-person lift. Please refer to the signage in the workshop about safe manual handling of heavy items.

  • Cross cut fence - this is a metal bar which attaches to the sliding beam and side table. The metal pegs on the fence can be slotted into holes on the side table, which lock it at common angles such as 90 degrees or 45 degrees. Alternatively, one of the pegs can be put into a channel in the side table, and set to any other angle before being screwed securely into place. More on this below.

  • Blades

    • Main Blade
    • The main blade is 300mm in diameter with a 30mm bore (centre hole), and spins towards the operator - meaning that it cuts through wood pushed against its cutting face. It is the energy of this blade spinning towards the operator that can “kick” material back towards you if it gets caught by the blade incorrectly.
    • Generally speaking, crosscut blades for the table saw have more teeth (to get a neater finish), whilst rip cut blades have fewer (to allow more waste to be cleared). Multi-material blades can also be fitted, which are suitable for wood and plastic.
  • Use a rip cut blade to cut WITH the grain of real wood

  • Use a crosscut blade for MDF, plywood and other artificial pressed wood products
    Sawblades_5F00_blow-out-part-41

    • No metal should ever be cut on our table saw - the potential for causing a fire is simply too high, given the amount of wood waste in and around the machine.
  • Tools - The tools needed to change the blade and set the riving knife are located next to the blades.

  • Riving knife (pronounced to rhyme with “driving”) - this is a curved strip of metal which sits just behind the blade, giving the teeth around 5mm of clearance. As the material moves across the blade, the riving knife keeps the two edges of the material apart, and helps keep the material moving in a perfectly straight line.

    This is vitally important
    It significantly reduces the risk of the material twisting or catching - which would cause a nasty kick.
    Kickback is one of the primary mechanisms of table saw injuries.


    Using a table saw without a riving knife is common in the US, but is terminally dangerous - and therefore not allowed in the UK, and definitely not at SLMS.

  • Blade Controls - These wheels control the position of the blade. This first one sets the blade height, and the knob on the wheel locks the position:


    the wheel on the side adjusts the angle of the blade; never trust that it is square:

    • Scoring blade
scoring blade not used
  • This is a small blade behind the main blade: Not currently fitted, and unlikely to be fitted in the future
  • Purpose is to reduce tear-out on surface - sticks 5mm above the surface of the bed, cuts the underside of a panel preventing surface chipping by the main saw blade

Prepare your material / Plan your cut

Click/tap to expand
  • Isolate the tool from the power supply, to reduce the risk of injury during set-up
    • As with any material going into one of our powerful and valuable tools - your material must be guaranteed free of screws/nails, etc… Do not put reclaimed timber through the table saw without discussing with a woodtech.
  • Your board must be able to lie flat on the bed and not twist or rock throughout the cut - this is a safety risk.
  • Likewise, if using the rip fence, the board must have a straight edge to ride along the fence - also a safety risk
  • Never “freehand” cut on the table saw

Rip cut or cross cut?

  • Most materials to be cut on the table saw are at least roughly rectangular. Consider your material - are you cutting along the longer length of the rectangle, or across the narrower width?
  • If you’re cutting down the length, this will generally be a rip cut
  • If you’re cutting along the width, this will generally be a cross cut
  • If in any doubt, ask a woodtech. Strangely shaped materials will typically be treated as a cross cut

Rip cut preparation:

(click to expand)
  • Never ripcut anything wider than it is long - ie. short side of a rectangle - as this will twist very easily and cause a kick.
    • You’ll be using the ripcut fence, which is parallel to the bed and doesn’t move during cutting.

    • Ensure the crosscut fence had been removed from the table saw, and stowed back where it belongs

    • Lift the guard, so that it is easier to access the blade for measuring. Whilst it’s visible, check that the riving knife looks straight and in line with the blade. Also check that the riving knife clears the blade, but only by around 3-5mm (no more than 8mm).

    • This requires you to have a straight edge on your material, perfectly parallel to the cut you want to make. If there isn’t such an edge, you’ll probably need to treat this as a crosscut. In some circumstances, you may be able to screw a straight edged offcut on to an uneven edge to act as a guide. Discuss with a woodtech if there is any doubt.

    • Adjust the ripcut fence:

      • Check you measurements, to make sure you know how wide to set the fence. You may wish to mark up a piece of scrap in the same way as your material, in order to check the settings are correct.
      • The end of the fence nearest the operator has a metal lever with a black knob on the end. Set this to the middle position - “unlocked”.
      • You can now push the fence from side to side, to get it in roughly the right place - you only need to be close for now - within around 2 cm. Once in position, set the lever to the top position - “Vernier”.
      • In the Vernier position, you can now use the silver knob on the left of the fence to “micro-adjust” the fence in either direction, to get the distance from the side of the blade to the side of the fence exactly correct. Your piece of scrap may be useful to check this visually!
      • Set the metal lever to the bottom position - this locks the fence in place.
    • the fence itself should be aligned to the end of the closest gullet in the saw blade

    • Mark up your cut position on the leading edge of your material - the bit that will be offered up to the blade first - remember to allow for kerf! ( the thickness of the blade)

Cross cut preparation:

(click to expand)
  • Is the material big enough to need the side table? If not you may be able to use this jig:


  • If cut is small enough that it only requires travel of 30cm(???), then it can be done without exposing the blade (without removing the safety finger).

  • Otherwise - Fit side table to sliding beam - ensure they are locked together (see details below)

  • Install cross cut fence and make sure it is fitted correctly to the side table (see below)

    • Many cross cuts will require the side table and cross cut fence, which is typically perpendicular to the blade (at 90 degrees), and will move with your material as it goes through the full length of the cut. However, the fence can be set at any angle between about 20 degrees and 160 degrees from the blade’s path - see oblique cuts section below…
  • Make sure that material is securely held against the crosscut fence and any sled at all times during cutting - by clamp or by hand. Never support the wood with both the crosscut and rip cut fence

    • Ideally, you want a flat edge which can sit against the fence, whatever angle you may need this set to. If there isn’t such an edge, then you will need to very thoroughly clamp the workpiece to the sliding beam, so that it cannot twist at all during the cut.

Removable Side Table / Sliding Beam Installation

(click/tap to expand)

*square the fence to the blade (it has a small amount of play), then tighten it down by tightening the two fence bolts. There should be 2 washers on the bolts to ensure they stay tight:

  • make sure the table is positioned on the beam with enough travel to complete your cut. Slightly loosen the two bolts holding the table to the sliding beam - just enough so it can move. Slide the beam as far forward as it can go. Move the table down the sliding beam so it is positioned like in the below photo. Tighten the two sliding beam bolts fully.

Done!

Oblique cut preparation:

Cribsheet (click to expand)

Adjusting Blade Height

(click/tap to expand)
  • The blade height is adjusted by the handwheel by the main operator controls of the machine:

  • Set the height of the blade. Release the locking nut on the wheel by hand (leftie-loosey!), and turn the wheel to raise or lower the blade. Set the blade height to be around 5mm taller than the height of your material (assuming you want to cut all the way through). You can do this by putting an offcut next to the blade, or by using the measurements displayed in the wheel you are turning. Once the blade height is correct, re-tighten the locking nut by hand.

  • Turn the wheel clockwise to raise the blade, the height is correct when it exceeds the workpiece thickness by 1-1.5cm. After adjustment you should lock the height with the small lock knob (hand tight).

  • Check the blade is tilted (or not) to the correct angle - it should have been left perfectly upright (90 deg). There is a similar wheel with locking nut located just inside the table saw body, to the right of the wheel you’ve just used (underneath the fence controls). Make sure the locking knob is hand tightened, whether you’ve adjusted the tilt or not.

Changing the Blade

(click/tap to expand)
  • Isolate the power to the machine in two places! Twist the wall isolator to “Off”. Always isolate before bringing body parts within 30cm of the blade.

  • Raise the blade guard and lock into place out of the way:

  • Remove safety stop/rubber bumper bar

  • Remove the sliding beam locking knob:

  • Push sliding beam to end of travel farthest from operator

  • Use a screwdriver to lock the spindle: Insert into hole on bed an turn slowly by hand (not touching teeth) until screwdriver drops and spindle is locked

  • Remove blade locking nut -note: LEFT HANDED THREAD (clockwise to loosen!) Note: the torque wrench (shown below) should only be used in the orientation shown (flat side towards blade) to avoid stressing the torque mechanism.

  • Take note of washers/spreader and inner reduction ring that fits spindle to blade - don’t lose the reduction ring - it may be stuck in the centre of the old blade!

  • Clean out any sawdust and slivers whilst tablesaw is open

  • Select new blade to fit (rip, cross, multicut?)- with min 200mm / max 300mm diameter

  • Remove old blade and fit new - make sure the inner ring is in place and the blade is the correct way around - teeth facing operator

  • Reassemble and torque the blade - make sure all the components are smooth, in order and flat against each other - the torque wrench will click when it is the correct tightness - REMEMBER LEFT HAND THREAD! - TURN COUNTER-CLOCKWISE TO TIGHTEN

  • If necessary (inspect, but usually when using a different sized blade) adjust the riving knife to be 3-5mm (no more than 8mm) from the new blade (following the contour) and at least the same height (or a little higher) to the blade teeth

  • The riving knife needs to be dead straight in line with the blade (this photo needs slight adjustment):

*Slide beam back to normal operating position (lined up with rear of the saw)


Clamps

(click/tap to expand)
  • Use clamps to hold smaller pieces of wood
  • Make sure to not use the rip cut fence and the clamps at the same time, remember we always want one bit of the wood free so that the blade doesn’t bind / kick.


using the fence to set the piece parallel to the blade. Do NOT make the cut in this state:

Move the fence away before making the cut:


Before Use

  • Set the guard to the right height using the wheels on the “elbow” of the arm that holds it. For material less than 1 ¼ inches (around 3 cm), this should be sat on the bed - but not too heavily! For thicker material, the guard should hang above the bed - at a height just above the thickness of your material. Make sure your material will fit under the guard.

  • Ensure the bed and out feed table are completely clear - remove any scraps, offcuts, screws, notes, phones, teacups, etc…

  • Ensure that you have sufficient space available at both ends of the blade for the full length of your cut - move any stacked wood, bins, or other obstacles as necessary.

  • Tell everyone around you what you are about to do - make sure anyone using the workbenches or lathe is aware. Advise them that this is a good time to put on ear defenders and masks (if needed). If doing a rip cut, notify those directly behind you.

  • Final checks - is the fence securely locked off and immobile? Is it in the right place? Is the blade at the right height and tilt? Are the blade adjustment wheel locking nuts tightened? Is the guard at the right height? Are you wearing all your PPE - mask, ear defenders, safety glasses?

Final Checks for all cuts!

  • Fences - never use both! Confirm angle of the crosscut fence is correct with an engineer’s square.
  • Guard height
  • Riving knife present, straight and correct distance from blade teeth
  • Blade height and angle correct - confirm with an engineer’s square or digital angle gauge
  • Ensure material is clamped as necessary, or that push sticks/sled are at hand
  • Entire tablesaw bed and off feed table clear of dross
  • PPE on and ready
  • Extraction is on
  • Tell everyone in the workshop that you’re going to use the tablesaw
  • ensure your surroundings are clear (move any ladders/boards on the wall nearby, move any other obstructing objects.

Making the cut

  • Turn on the extraction
  • Power on the machine
  • when ripping:
    • Do not stand immediately behind the board - stand slightly to the left
    • Ensure you put downward pressure on the board as you push it through - it must stay flat on the bed - sometimes it wants to rise.
    • No hands within 30cm of the blade - use a push stick
    • push the piece all the way through past the blade with a push stick
      • do not use the push stick until the edge of the board gets onto the bed - you don’t want to pry the board upwards.
    • the board must lay flat against the bed of the saw and against the fence throughout the entire cut. Apply the necessary downward and inward pressure to ensure this. Consider using a feather board.

Cleaning up after usage

  • Turn off separate table saw extraction
  • Remove side table / sliding beam (if used)
  • Put away any clamps / jigs you used
  • Hoover up any sawdust that is left over
  • Leave blade guard down to avoid any accidental injuries
  • Be sure to isolate the power and sign out of tool control

Notes for delivering induction (to be depricated):

Cribsheet (click to expand)

1. Initial lecture - intended to be up to 45 mins in length

What the table saw does:

  • Big, accurate saw - very good at cutting straight lines - both cross cut and ripcut

  • Compare briefly to bandsaw and mitresaw - discuss a few tasks you would use the tablesaw to complete

  • Induction will cover safety and basic technique - if doing anything more complex, then discuss with a woodtech first

  • No metal ever to be cut on the tablesaw. Plastic could be cut but would require special blade - discuss with woodtechs.

What are the risks?

See the Risk Assessment…

PPE

  • Recap usual dress rules for the woodshop - tie back everything, and no gloves!

  • Use push sticks or sleds to prevent your body coming within 30cm (1ft) of the blade. Except when using sled with a solid guard between hand and blade.

  • Always use extraction

  • Goggle, masks, ear defenders

  • Isolate tool in two places before going within 30cm (1ft) of the blade - just using tool control doesn’t count. Use both the twistable isolators.

  • No lone working

  • Don’t use tools when tired

Anatomy of the tool:

  • Power control/switches. Include tool control - reminder that responsibility for any injury is down to the person whose fob is in use.

  • Emergency stops. Reminder it’s easy to hit with knee - slowing blade is more dangerous. Use mushroom to stop, not isolators.

  • Bed - mention the of feed table and 8ft is maximum length that a single person can cut

  • Guard and how to raise and lower - the guard should always be as low as possible - sitting on bed for any material up to 18mm (~3/4 inch) thick. NB - current advise not to use anti-kick claws as they require more work to function properly.

  • Extraction - reminder about checking all the right gates are open/closed.

  • Ripcut fence - and how to adjust. Should usually be “vertical”, but can be turned onto it’s side when carrying out a fine trim and needing to get under the guard

  • Sliding beam - should always be locked in place if movement not required for current cut. Clamps can be used to hold a small piece to the sliding beam for cross-cutting.

  • Crosscut fence - large metal bar which attaches to the side table

  • Riving knife - keeps material separated and in a straight line after passing across blade. Reduces risk of twisting and catching. Riving knife should be around 5-8mm clear of the the blade tips. Reiterate that riving knife is extremely important, even though it is often not used in the US

  • Control for changing main blade height - should be set so that gutter on teeth is a few mm above the surface of the material

  • Control for changing main blade angle - should be left perfectly vertical

Prepare your material

  • Ensure material is free of nails and screws - beware reclaimed timber.

  • If you’re cutting along the length of a rectangular material, this will be a ripcut

  • If you’re cutting across the narrower width of a rectangular material, this will be a crosscut

  • If in doubt, discuss with a woodtech

  • Crucially - ensure that any “reference edge” which will be pressed up against a fence is perfectly straight - if not, screw on a straight piece to serve this purpose

2. Demo/usage - intended to take 20 minutes each for 2 inductees, plus time for demo and questions:

  • Inductor demonstrates a ripcut, then changes the blade, attaches the side table, and demonstrates 2 cross cuts (one with material in front of fence, one with material behind fence).

  • _Get inductees to repeat all the above. Ensure that both people in each pair are getting equally involved.

  • Invite everyone to give feedback and ask questions as each pair practices.


Maintenance (woodtechs only)

(click to expand)
  • Periodic cleaning of the separate extractor
  • Sawdust fills up underneath the inside of the machine - hoover this
  • Check riving knife for straightness / adjustment
  • Lubricate machine - see manual below
  • Check e-stops are functioning properly
  • Check for dull blades and replace dispose of old ones properly

Videos

10 common dangerous things people do with table saws - a good overview of some common mistakes people make on table saws, worth a watch. Caveats: we don’t allow the removal of the blade guard, unless using a jig that keeps the blade covered through the entire cut, and similarly don’t allow non-through cuts.

Overview of kickback and how it occurs - he has removed the blade do demonstrate, we keep our blade guard on.

References

Manual: SI12SW Operations.pdf (952.8 KB)
Parts catalogue: SI 12 SW.pdf (914.7 KB)
HSE Safety Reference: HSE table saw information sheet.pdf (3.4 MB)

1 Like